歐能達主營YT無機活性微晶保溫砂漿,YT無機改性保溫材料系統,杭州外墻保溫材料,杭州無機保溫砂漿等!   聯系我們
杭州歐能達建筑材料有限公司
24小時服務熱線:0571-86551319
首頁: 資訊中心 >> 行業資訊

資訊中心 News

產品介紹

不同住宅裝修怎么樣選擇保溫裝飾一體板
不同住宅裝修怎么樣選擇保溫裝飾一體板
文章來源:本站原創  作者:網站管理員  瀏覽:7 更新時間:2019-12-02 07:38:19

 為大家介紹不同的住宅對保溫裝飾一體板的要求:

 
  1.高度大于等于100m的建筑,其保溫材料的燃燒性能應為A級。保溫裝飾一體板廠家是置于建筑物墻體表面的保溫及裝飾系統保溫效果優秀并且長期,熱橋作用少,節能保溫效果好。
  2.高度大于等于60m小于100m的建筑,其保溫材料的燃燒性能不應低于B2級。當采用B2級保溫材料時,每層應設置水平防火隔離帶。
 
  3.高度大于等于24m小于60m的建筑,其保溫材料的燃燒性能不應低于B2級。當采用B2級保溫材料時,每三層應設置水平防火隔離帶。
 
  其他民用建筑應符合以下:
 
  1.高度大于等于50m的建筑,其保溫材料的燃燒性能應為A級。
 
  2.高度大于等于24m小于50m的建筑,其保溫材料的燃燒后性能不應低于B1級。其中,當采用B1級保溫材料時,每兩層應設置水平防火隔離帶。
 
  3.高度小于24m的建筑,其保溫材料的燃燒性能不應低于B2級。其中,當采用B2級保溫材料時,每層應設置水平防火隔離帶。 防護層 應采用不燃或難燃材料做防火層,防護層應將保溫材料完全覆蓋。保溫裝飾一體板 首層的防護層厚度不應小于6mm,其他層不應小于3mm. 防火隔離帶 按本規定需要設置防火隔離帶時,防火隔離帶應采用A1(A)級保溫材料沿窗口上沿位置與基層墻面全面積粘貼,高度宜與保溫裝飾一體板的寬度一致,且應不小于300m,豎縫填縫材料應采用A1(A)級同質材料。 防火隔離措施 保溫裝飾一體板使用可燃保溫材料時,當保溫材料表面及側面均采用玻纖網格布增強聚合物砂漿或其它無機非金屬材料防護層包裹(防護層厚度不小于3mm)等防火處理措施后可適當提高其燃燒性能等級。
 

To introduce different residential insulation decoration of one board requirements: 1. If the height of the building is more than or equal to 100m, the burning performance of the insulation material should be a class. Heat preservation and decoration one-piece board factory is placed in the building wall insulation and decoration system insulation effect is excellent and long-term, Thermal bridge, less role, energy-saving insulation effect. 2. For buildings with a height of 60m or less than 100m, the combustion performance of the insulation material shall not be lower than grade B2. When B2 class insulation material is used, each layer shall be provided with a horizontal fire-proof isolation belt. 3. If the height of the building is greater than or equal to 24m and less than 60m, the combustion performance of the insulation material should not be lower than grade B 2. When B2 class insulation material is used, a horizontal fire-proof isolation belt should be installed on every third floor. Other civil buildings shall conform to the following: 1. If the height of the building is greater than or equal to 50 meters, the burning performance of the insulation material should be a class. 2. For buildings with a height of 24M or less than 50m, the post-combustion performance of the insulation material shall not be lower than Grade B1. Among them, when using B1 class insulation material, every two layers should be set up level fire-proof isolation belt. 3. For buildings less than 24m in height, the flammability of the insulation material shall not be lower than grade B2. Among them, when using B2 class insulation material, each layer should be set up level fire-proof isolation belt. Protective Layer, should use non-combustible or fire-resistant materials as a fire layer, protective layer should be completely covered with thermal insulation materials. Insulation decorative one board, the first layer of the protective layer thickness should not be less than 6mm, the other layer should not be less than 3mm. The fire-proof isolation belt shall be pasted with a 1A class thermal insulation material along the upper edge of the window and the base wall surface in an all-round way, and the height shall be consistent with the width of the thermal insulation decorative one-piece Board And should not be less than 300m, vertical joint materials should be used A1A homogeneous material. Fire insulation measures, Thermal Insulation Decorative one-piece Board when using combustible thermal insulation materials, when the surface and side of thermal insulation material are treated with fire protection measures such as Glass Fiber Mesh cloth reinforced polymer mortar or other inorganic non-metallic material protective coating thickness not less than 3mm, its combustion performance can be properly improved.

Tag:
2019灰色暴力网赚 香港开奖结果2019+开奖结果 天天网赚靠谱吗 大资本网址 华夏彩票注册 河北快3基本走势 海南4+1 海南4+1 19年网赚钱商机 山东群英会手机版